I have been working on an 8-string C6 lap steel for a while now, when time and the winter weather allow. That garage workshop is pretty chilly. I've decided to use reclaimed timber throughout. The body is Brazilian mahogany from old door frames from an old folks' home. I had to put the pieces together edge to edge using glue and dowels.
The join is concealed by 1/4 inch strips of Honduran mahogany - much lighter in colour - from an old bed headboard. This was mouldering away in the back of a barn at my wife's livery stable where she keeps her horses. Under the peeling veneer was this beautiful rare wood, you don't see it imported any more. I cut up the rest to make two pedal steel bodies.
The fretboard is a piece of oak - an offcut - from a recycling centre. I cut the fret grooves on my mill with a 1.8mm bit. The "frets" are ebony stringing from a marquetry supplier. The fret markers are 8mm, 6mm and 5mm black mother of pearl dots from Pietra Dura, a UK supplier. These photos show the fretboard after insetting the frets and dots, and rough sanding. I plan to inlay a bird at the end of the fretboard between the 24th fret and the pickup.
For me, the pleasure is in exploring what I can do, discovering techniques and making tools as I go.
My first lap steel
My first lap steel
- Attachments
-
- Close-up showing the MOP dots
- LapSteelFretBoard 2.jpg (127.88 KiB) Viewed 13374 times
-
- Overall view of the fretboard
- LapSteelFretBoard 1.jpg (80.2 KiB) Viewed 13374 times
-
- Posts: 76
- Joined: Thu Apr 03, 2014 12:42 pm
Re: My first lap steel
looking good, Will
Re: My first lap steel
Thanks Jason, spent a fair bit of time this weekend milling the "steps" - to hold the machine heads - from some 1" square section bar. I have the outside steps done, but not the inside. This game takes a deal of time! But it's all time well spent developing skills for the "biggie" - a pedal steel.
Re: My first lap steel
I've been meaning to update you all on progress for a while, but have now got as far as getting all the parts together and doing a trial fit. I didn't want to do the banding around the edges, the sunburst and the inlay if in fact it wasn't strong enough and wouldn't sound right. So yesterday I took the plunge, fitted everything and put a set of strings on, using a jack socket soldered direct to the pickup lead. I haven't fitted and wired up the volume and tone controls yet, although the body is ready for them.
It sounds fine, good tone and holds its tune. I'm very pleased. Now to do the fine detail to make it look nice.
It sounds fine, good tone and holds its tune. I'm very pleased. Now to do the fine detail to make it look nice.
- Attachments
-
- Lap-Steel-20150904-4.jpg (460.46 KiB) Viewed 13005 times
-
- Lap-Steel-20150904-2.jpg (397.07 KiB) Viewed 13005 times
-
- Lap-Steel-20150904-1.jpg (436.93 KiB) Viewed 13005 times
Re: My first lap steel
Looks good Will, I might do an 8 string lap next.
Best Regards Ron Mc
Best Regards Ron Mc
Re: My first lap steel
this guitar looks very good
Re: My first lap steel
Thanks guys, for something where I'm feeling my way as I go, I'm pleased with how it's turning out. Now I have to take it apart and prep it for sunburst, lacquer, binding etc. I may put an inlay in the keyhead area too, under the strings. The eagle on the end of the fretboard is going to take a lot of care. I wasn't willing to go further with that until I knew it was going to work in terms of holding its tune etc. That mahogany isn't more than 26mm thick. It's only the fretboard that gives it enough strength I think.
-
- Posts: 4
- Joined: Sat Apr 27, 2019 12:27 am
Re: My first lap steel
What company did you get your nut and bridge from. That what I'm looking for for my first 8 string Lap Steel ...
"If it don't have a Steel...It ain't REAL!!"
Re: My first lap steel
Great job! Being a tool lover myself I would love to see pictures of the tools you have made. Especially interested in tools pertaining to guitar building! Thanks John