fretboard etching
fretboard etching
I'm new to steel building. I'm sure someone here etches their own aluminum fretboards & I'd like to try it. What methods have anyone used? Thanks for the info
Re: fretboard etching
Hi Marc, That's news to me. Let's hear it folks. Might be a heck of an idea.
http://benrom.com/
21 BenRom pedal steel guitars, a Nash 112 and a 1967 TOS Milling machine with many cutters making one hell of a mess on the floor.
21 BenRom pedal steel guitars, a Nash 112 and a 1967 TOS Milling machine with many cutters making one hell of a mess on the floor.
Re: fretboard etching
I was under the impression that the old Fender Stringmaster & Deluxes had etced aluminum fretboards.
Re: fretboard etching
oK that might very well be. Right now I dont even know what type of acid you would use tyo etch with; how to get nice sharp lines, how to prevent to acid from running all over..... Keep researching and sharing as you go along.
http://benrom.com/
21 BenRom pedal steel guitars, a Nash 112 and a 1967 TOS Milling machine with many cutters making one hell of a mess on the floor.
21 BenRom pedal steel guitars, a Nash 112 and a 1967 TOS Milling machine with many cutters making one hell of a mess on the floor.
-
- Posts: 517
- Joined: Sat Dec 11, 2010 11:44 am
- Location: Gallatin, Tennessee, USA
Re: fretboard etching
The new MSA's have a fretboard which appears to be stamped as opposed to etched. Don't know. Might be a booger-bear to keep clean.
Re: fretboard etching
Check out:
http://www.nontoxicprint.com/etchzincsteelaluminum.htm
A forum on etching, with many people adding their 2 cents, is at:
http://www.finishing.com/205/56.shtml
Richard: re keeping it clean. Would it clean easier if it were varnished?
http://www.nontoxicprint.com/etchzincsteelaluminum.htm
A forum on etching, with many people adding their 2 cents, is at:
http://www.finishing.com/205/56.shtml
Richard: re keeping it clean. Would it clean easier if it were varnished?
Conceive, believe, achieve!
- Georg
- Posts: 457
- Joined: Tue Nov 03, 2009 10:38 am
- Location: Mandal, VA, Norway & Weeki Wachee, FL, USA
- Contact:
Re: fretboard etching
Easiest to clean if it is etched, or milled, negative, I think. Frets etched low all the way across, and a line etched along the edge.
Haven't done any etching since I quit making circuit-boards that way in the early 80s. After that I used a mill for circuit-board prototyping and anything else thinner than about 4 millimeter.
For circuit-boards it was easy enough to spray on a light-sensitive film, force down plastic-film with "shapes" on top of the board and expose to UV-light. I then etched in stirred acids under control - I used pulsating air-injection for uniform stirring, and rinsed boards thoroughly in clean water before drying equally thoroughly off and applying protective lacquer.
Have never tried etching on aluminum, so know nothing about which acid to use.
Haven't done any etching since I quit making circuit-boards that way in the early 80s. After that I used a mill for circuit-board prototyping and anything else thinner than about 4 millimeter.
For circuit-boards it was easy enough to spray on a light-sensitive film, force down plastic-film with "shapes" on top of the board and expose to UV-light. I then etched in stirred acids under control - I used pulsating air-injection for uniform stirring, and rinsed boards thoroughly in clean water before drying equally thoroughly off and applying protective lacquer.
Have never tried etching on aluminum, so know nothing about which acid to use.
-
- Posts: 517
- Joined: Sat Dec 11, 2010 11:44 am
- Location: Gallatin, Tennessee, USA
Re: fretboard etching
Dave-M -
It would appear that the frets, themselves, plus the outer edges are raised. Very smooth surface. I, personally, love the appearance of it although it conjures visions of Q-tips and Windex when changing strings. Might not be so bad, though. Might also be a small penalty for something which is different and somewhat elegant.
http://www.msapedalsteels.com/html/legend.html
MSA millenium and Legend.
Richard
It would appear that the frets, themselves, plus the outer edges are raised. Very smooth surface. I, personally, love the appearance of it although it conjures visions of Q-tips and Windex when changing strings. Might not be so bad, though. Might also be a small penalty for something which is different and somewhat elegant.
http://www.msapedalsteels.com/html/legend.html
MSA millenium and Legend.
Richard