Any chance of finding someone who'd sell some homemade fingers that could be used to make a basic changer. Needing a finger that
could take an axle hole on one end and a small hole for a rod or cable on the other. Just to do raises, no lowering.
They would be shaped more or less like the top part of an exclamation mark. Probably about 3 inches in length.
If they had a 1/2" 5/8" hole for an axle could get by with four or five of these since they could be combined with some other short fingers I already have.
If they are different I guess 10 would be needed.
Have about everything else to build a sort of lap steel/pedal steel idea, but don't have any way to make metal parts.
Would be willing to pay for these if I can find some.
Thanks.
Changer fingers?
-
- Posts: 13
- Joined: Mon Oct 15, 2012 10:15 pm
Re: Changer fingers?
I'D LIKE A SHOT AT THAT - NEED SOME MORE SPECIFICS.
HAVING TROUBLE WITH NET - CALLME @1-803-684-5519.
THESE FINGERS ARE PUSH-PULL ON MY STEEL BUILDS THAT
I'VE BEEN SELLING.THANKS! PASTOR BRUCE
HAVING TROUBLE WITH NET - CALLME @1-803-684-5519.
THESE FINGERS ARE PUSH-PULL ON MY STEEL BUILDS THAT
I'VE BEEN SELLING.THANKS! PASTOR BRUCE
- Attachments
-
- Mhgny2a.jpg (94.19 KiB) Viewed 10967 times
Re: Changer fingers?
The finger on the right side is about what it would look like.......
download/file.php?id=1424
download/file.php?id=1424
Length about 3 to 3 1/2" and about standard width used in a psg. Might use spacers to get a little more string spacing than a normal 10 string psg.
Haven't seen what you are using on your 6 string psg's, but thats probably about what's needed. Except I'm using 10 strings.
download/file.php?id=1424
download/file.php?id=1424
Length about 3 to 3 1/2" and about standard width used in a psg. Might use spacers to get a little more string spacing than a normal 10 string psg.
Haven't seen what you are using on your 6 string psg's, but thats probably about what's needed. Except I'm using 10 strings.
-
- Posts: 13
- Joined: Mon Oct 15, 2012 10:15 pm
Re: Changer fingers?
FRIEND GAMAC,
WOULD THIS DO ? NOT CLEAR ON AXLE DIAM. - IS IT 1/2
OR 5/8 INCH? THOUGHT 2 PULL HOLES WOULD OFFER SOME ADJUSTMENT OF LEVERAGE.1/4 INCH THICK X 3/4 OR 1 INCH
WIDE STOCK WOULD BE USED.POLISHED ON TOP SECTION.
PB
WOULD THIS DO ? NOT CLEAR ON AXLE DIAM. - IS IT 1/2
OR 5/8 INCH? THOUGHT 2 PULL HOLES WOULD OFFER SOME ADJUSTMENT OF LEVERAGE.1/4 INCH THICK X 3/4 OR 1 INCH
WIDE STOCK WOULD BE USED.POLISHED ON TOP SECTION.
PB
- Attachments
-
- fingers.jpg (15.11 KiB) Viewed 10926 times
-
- Posts: 13
- Joined: Mon Oct 15, 2012 10:15 pm
Re: Changer fingers?
SORRY FOR THE DELAY BUT HERE ARE THE DETAILS OF
THE SPLITTER UNDER THE STEEL.HOPE THIS HELPS. IT CAN BE DONE ON THE CROSS AXLE ITSELF AS MANY ARE , BUT I'VE
USED THIS SYSTEM TOO WITHOUT DIFFICULTY.IT IS
SIMILAR TO SHOBUD MAVERICK ARRANGEMENT.SOME PICS
OF THOSE ARE ON STEELGUITARFORUM IF YOU CARE TO SEE
MORE .WORKS WELL FOR YOUR APPLICATION,I THINK.
PASTOR BRUCE
THE SPLITTER UNDER THE STEEL.HOPE THIS HELPS. IT CAN BE DONE ON THE CROSS AXLE ITSELF AS MANY ARE , BUT I'VE
USED THIS SYSTEM TOO WITHOUT DIFFICULTY.IT IS
SIMILAR TO SHOBUD MAVERICK ARRANGEMENT.SOME PICS
OF THOSE ARE ON STEELGUITARFORUM IF YOU CARE TO SEE
MORE .WORKS WELL FOR YOUR APPLICATION,I THINK.
PASTOR BRUCE
Re: Changer fingers?
I tried something similar to that, but ended up using two cables to a pedal where there were two pulls involved.
Doing that seemed to lessen the force needed to raise the strings.
A number of stock steel guitar pedals have two holes for pedal rod connectors so this was easy to
do. The cables were attached to right and left sides of the pedal.
Still don't have an ideal design for a pedalbox. Have tried wood and pvc pipe, but
haven't found anything that can't be improved upon yet.
Doing that seemed to lessen the force needed to raise the strings.
A number of stock steel guitar pedals have two holes for pedal rod connectors so this was easy to
do. The cables were attached to right and left sides of the pedal.
Still don't have an ideal design for a pedalbox. Have tried wood and pvc pipe, but
haven't found anything that can't be improved upon yet.
-
- Posts: 13
- Joined: Mon Oct 15, 2012 10:15 pm
Re: Changer fingers?
JUST FOR THE RECORD,MY FINGERS ARE ACTUALLY
"PULL-RELEASE" - NOT PUSH-PULL AS STATED ABOVE.
WHERE DID I GET THAAAAT???? MUST'VE BEEN ONE OF THOSE
LONG DAYS. SORRY FOR THE ERROR!
THANKS. PB
"PULL-RELEASE" - NOT PUSH-PULL AS STATED ABOVE.
WHERE DID I GET THAAAAT???? MUST'VE BEEN ONE OF THOSE
LONG DAYS. SORRY FOR THE ERROR!
THANKS. PB
Re: Changer fingers?
"....JUST FOR THE RECORD,MY FINGERS ARE ACTUALLY
"PULL-RELEASE" ...."
Any change of seeing a diagram of how you set this up. It's not too hard to
achieve a string raise, but a lot harder to install something that will
handle a lower as well.
[img]emm8-2p-undchgCLOSE.jpg[/img] Here's an example of "pull but no release"
"PULL-RELEASE" ...."
Any change of seeing a diagram of how you set this up. It's not too hard to
achieve a string raise, but a lot harder to install something that will
handle a lower as well.
[img]emm8-2p-undchgCLOSE.jpg[/img] Here's an example of "pull but no release"